Home and desk
This tool generates pegboard hooks, shelves and rings and exports them as STL. Pick the board: 40 mm pitch with 5x15 mm vertical slots, or classic pegboard with 25.4 mm (1 inch) pitch and Ø6 mm holes. Then choose the hook type and enter length and tip lip in millimetres.
Each hook grips the board at two points: the upper tab passes through a slot and locks with a lip that drops 6 mm behind the board, and the lower pin enters the next slot down. On slotted boards the tab is 5 mm minus twice the tolerance, 4.6 mm at the default 0.2 mm, which also fits the 5.2 mm slots of printed boards.
Free, no sign-up. Change the sizes in millimetres and download the STL.
Each variant is the same template with different settings. Follow the link and the editor opens with those values.
Board type: 40 mm pitch, 5x15 slots · Hook type: Single hook · Length: 50 mm +5
Open this variant: Single hook, 40 mm pitch board
Board type: 40 mm pitch, 5x15 slots · Hook type: Shelf · Length: 60 mm +5
Open this variant: Shelf, 40 mm pitch board
Board type: 25.4 mm pitch, Ø6 holes · Hook type: U holder · Length: 50 mm +7
Open this variant: U holder, 1 inch pegboard
Board type: 40 mm pitch, 5x15 slots · Hook type: Ring · Length: 50 mm +5
Open this variant: Ring, 40 mm pitch boardThese values are edited in the editor's template panel. A number outside the range is clamped to the nearest limit automatically.
| Size | Range | Default |
|---|---|---|
| Shape | ||
| Board type | 40 mm pitch, 5x15 slots, 25.4 mm pitch, Ø6 holes | 40 mm pitch, 5x15 slots |
| Hook type | Single hook, Double hook, Straight peg, U holder, Shelf, Ring | Single hook |
| Dimensions | ||
| Length | 15–150 mm | 50 mm |
| Tip lip * | 0–40 mm | 12 mm |
| Thickness | 3–12 mm | 6 mm |
| Body width | 5–60 mm | 8 mm |
| U inner width * | 8–60 mm | 20 mm |
| Ring inner diameter * | 10–80 mm | 25 mm |
| Board fit | ||
| Slot tolerance | 0–0.6 mm | 0.2 mm |
| Board thickness | 2–8 mm | 5 mm |
| Hole diameter * | 4–8 mm | 6 mm |
Sizes marked with a star appear in the panel only when the related shape, style or option is active.
Slotted boards have slots 40 mm apart, 5 mm wide and 15 mm tall on a 5 mm panel. Classic pegboard has Ø6 mm holes 25.4 mm apart on a 3.2 or 6.4 mm panel. Board thickness and hole diameter are parameters, so other boards work too.
The single hook holds a tool with an upturned lip; the double hook adds a shorter second level. The straight peg rises at 10° and ends in a knob. The U holder cradles round handles, the ring carries rolls and cable bundles, and the shelf is a tray with a 45° brace.
Hold the upper tab at an angle, pass it through the slot and rotate the hook down. The lip settles behind the board and the lower pin drops into the slot below.
Raise the slot tolerance if it will not go in, lower it if it wobbles. Printed boards have slightly wider slots, so 0.1 mm often fits firmer.
On its side the layer lines run along the hook. Upright hooks tend to split between layers under load; side printed ones resist bending far better.
This tool builds a screw-on wall hook to your measurements and exports it as an STL. Pick a hook style, type the plate size and how far the hook should reach out in millimetres, set the screw holes, and the model is computed in your browser.
Sizes and details: Wall hook
This tool generates a divider box at the outside dimensions you type in and exports it as an STL. Enter width, depth and height, pick the number of rows and columns, and the divider walls split the interior into equal cells while the model updates in your browser.
Sizes and details: Divider box
This page opens the DrawSTL L bracket template: a parametric right-angle corner bracket with screw holes that you size in millimetres and download as a print-ready STL. You give the horizontal arm, the vertical arm, the width and the thickness, and the holes are spaced evenly along each arm.
Sizes and details: L bracketOpen the template in the editor, enter your values and download a print-ready STL. No account needed.