Home and desk
This tool generates a rack with a row of holes that keeps hand tools on the wall or at a desk edge, and exports it as an STL. Enter the hole type, number, size and spacing, choose a mount, and the model is built in your browser.
Round holes hang screwdrivers by the handle, long slots hold pliers and scissors by the joint, and the mixed option alternates both. Every mount type is built in an orientation that prints without supports.
Free, no sign-up. Change the sizes in millimetres and download the STL.
Each variant is the same template with different settings. Follow the link and the editor opens with those values.
Hole type: Round (screwdrivers) · Number of holes: 8 · Hole diameter / slot width: 8 mm +3
Open this variant: 8 screwdrivers, back plate on bed
Hole type: Slot (pliers, scissors) · Number of holes: 4 · Hole diameter / slot width: 10 mm +4
Open this variant: 4 plier slots
Hole type: Mixed · Number of holes: 6 · Mounting: Desk edge
Open this variant: Mixed rack for a desk edgeThese values are edited in the editor's template panel. A number outside the range is clamped to the nearest limit automatically.
| Size | Range | Default |
|---|---|---|
| Shape | ||
| Hole type | Round (screwdrivers), Slot (pliers, scissors), Mixed | Round (screwdrivers) |
| Number of holes | 1–16 | 6 |
| Dimensions | ||
| Hole diameter / slot width | 3–30 mm | 8 mm |
| Slot length * | 8–60 mm | 22 mm |
| Hole spacing (centres) | 8–80 mm | 22 mm |
| Shelf depth | 15–80 mm | 40 mm |
| Thickness | 2.4–12 mm | 5 mm |
| Back plate height * | 20–150 mm | 50 mm |
| Mounting | ||
| Mounting | Wall screws, Desk edge, No mounting | Wall screws |
| Screw diameter * | 3–6 mm | 4 mm |
| Countersink * | On / Off | On |
| Depth resting on desk * | 20–80 mm | 35 mm |
| Edge lip height * | 6–40 mm | 15 mm |
| Printing | ||
| Print orientation * | Back plate on bed, Upright, 45° brace | Upright, 45° brace |
Sizes marked with a star appear in the panel only when the related shape, style or option is active.
Spacing is measured centre to centre. To keep at least 2 mm of material between holes, it grows automatically when needed and a note appears in the panel. The shelf depth also adjusts so the holes fit.
With wall screws, the back plate extends into an ear on each side with a countersunk hole. With the desk edge mount, the rear part rests on the desk, a lip underneath presses against the front edge and two screws hold it down. The unmounted version works with double sided tape or magnets.
Printed upright on the brace, the layers carry the shelf load better. Printing with the back plate on the bed is faster and fine for light tools.
With the back plate on the bed the holes lie horizontal. The 45° teardrop tip lets their roof print without supports.
That depends on material, infill and screws. For heavy pliers, print upright with the brace, use 30% infill and at least two screws in wall plugs.
This tool builds a screw-on wall hook to your measurements and exports it as an STL. Pick a hook style, type the plate size and how far the hook should reach out in millimetres, set the screw holes, and the model is computed in your browser.
Sizes and details: Wall hook
This page opens the DrawSTL L bracket template: a parametric right-angle corner bracket with screw holes that you size in millimetres and download as a print-ready STL. You give the horizontal arm, the vertical arm, the width and the thickness, and the holes are spaced evenly along each arm.
Sizes and details: L bracket
This tool generates a pen holder at the diameter and height you type in and exports it as an STL. Choose the body shape, set wall and floor thickness, add compartments if you want them, and the model updates in the browser so you can spin it and check.
Sizes and details: Pen holderOpen the template in the editor, enter your values and download a print-ready STL. No account needed.